Skip to main content
Free Delivery  ·  COD Available  ·  15-Day Returns
Pricio
UHF&VHF Antenna MMDVM Hotspot Support P25 DMR YSF for Raspberry pi — image 1
Hover to zoom

1 / 5 · Click to enlarge

Pricio

UHF&VHF Antenna MMDVM Hotspot Support P25 DMR YSF for Raspberry pi

5.05 ratings
AI Summary
Electronics for everyday users

The UHF&VHF Antenna MMDVM Hotspot Support P25 DMR YSF for Raspberry pi by Pricio is a mid-range electronics designed for everyday users. 100% of buyers rate it 4★ or above.

₹3,199-19%
MRP:₹3,949Save ₹750
Free Shipping💵 COD Available

Available Offers

Free Delivery on this order. No minimum order value.

15-Day Easy Returns — hassle-free return & full refund.

Secure Payment — 100% safe checkout with UPI, Cards & Net Banking.

19% Off — you save ₹750 on this product!

Type: No Shell

No Shell
Total: ₹3,199
Buying tip: A quality investment for dependable performance and premium build quality.
Estimated delivery: 4 Aug18 Aug
Free Shipping
Pan India delivery
15-Day Returns
Hassle-free policy
Secure Payment
Razorpay protected
Quality Assured
Vetted products only

Available Offers

💳

5% Cashback

Pay with UPI & get 5% cashback (up to ₹50) via Razorpay

🏦

No-Cost EMI

Available on select bank cards at checkout. 0% interest for 3 months.

📦

Free Shipping

Free delivery on all orders. No minimum order value.

💵

Cash on Delivery

COD available on orders up to ₹5,000 across India.

Ideal For

Everyday convenience
Share:
SKU: bg-2018078Category: Electronics

About This Product

The UHF&VHF Antenna MMDVM Hotspot Support P25 DMR YSF for Raspberry pi by Pricio is a mid-range electronics designed for everyday users. It delivers reliable performance at an accessible price.

Customer Verdict

100% of buyers rated this product 4 stars or above.

Why Buy from Pricio?

Pricio sources this product directly, cutting out multiple middlemen. Every order includes free shipping, a 15-day return policy, and secure payment via Razorpay.

STM32_MMDVM_HS HAT Guide new pi4b need remove R1 Resistor. STM32_MMDVM_HS HAT Rev1.7 Guide 1.Hardware add (SDA,SCL)R20,R21 Connect stm32 i2c 2 bus to OLED,and raspi. oled message pwr on without RPI using mmdvm_hs custom fw,and i2c 2 bus.

2.Support i2c communition with raspi

Setting For Pi-star software and raspberry hardware (rpi 0-3) new pi4b need remove R1 Resistor.

Controller Mode: Simplex Node

Radio Frequency: Freq:144-148,219-225,(Main Band)420-475,842-950

Example: 438.000000

Radio/Modem Type: STM32-DVM(GPIO)

14.7456 TCXO with RXOFFSET=0 TXOFFSET=0 Quick start: 1.download image https://www.pistar.uk/downloads/ write it to card

2.insert card to rpi

3.wait to boot 5 minutes connect wifi Pi-star-setup pass raspberry

4.open http://pi-star/admin/ 5.set freq ,dmr id ,dmr mode,add home's wifi ssid... Default Username: pi-star Default Password: raspberry to support i2c communication change MMDVM_HS code(by Andy Uribe CA6JAU)->Config.h // Host communication selection: //#define STM32_USART1_HOST //#define STM32_USB_HOST #define STM32_I2C_HOST to disable i2c 2 to raspi and oled just remove R20,R21 update new FW: (pi-star / expert / ssh access / user :pi-star pass:raspberry) sudo pistar-mmdvmhshatflash hs_hat ps:update new FW no oled pwr on message. mode info pls visit www.mmdvm.club



Product Safety Information

Setup Guide

1
Identify the pins
Locate VCC (power), GND (ground), and data pins (SDA/SCL for I2C, MOSI/MISO for SPI, or TX/RX for UART). Refer to the pinout diagram on the product page.
2
Wire to your microcontroller
Connect VCC to 3.3V or 5V (check the module spec), GND to GND, and data pins to the appropriate GPIO pins on your Arduino or Raspberry Pi.
3
Install libraries
In Arduino IDE, go to Sketch → Include Library → Manage Libraries and search for the sensor library. Install the recommended version.
4
Upload example sketch
Open File → Examples → [library name] → Basic Example. Upload to your board and open Serial Monitor to view output.
5
Calibrate if needed
Some sensors (temperature, humidity, distance) may need a short warm-up period or calibration. Run the calibration sketch if provided.